Cisco 700-150认证历年真题与练习测试，Cisco销售专业考试700-150 ICS | 思博网络

In the multi-level RR scenario, a large number of secondary RRs will be connected to the primary RR, which may lead to BGP of the primary RR. The routing table overflows, what method can be used to reduce the risk of overflowing the routing table of the advanced RR BGP?

In the OSPFv3 network shown in the figure, the interconnected ports of R1, R2, and R3 have OSPFv3 enabled, and the Router ID of each device is 10.0.XX, where X is the device number. Check the detailed information of a certain LSA on R3. From the output information, it can be inferred that the LSA is generated by R2, and it describes the IPv6 prefix address associated with the Network-LSA.

Assuming that the neighbor relationship between BGP routers has been established successfully, the configuration on R1 is as shown in the figure. Which router can the route entry 10.10.10.0/24 advertised by R1 be delivered to?

According to this figure, it can be known that in VLAN 300, on 2020-06-04, from 17:22:38 to 17:22:44, how many MAC flaps does the 00e0-fc3d-3bdb have?

The equipment operating environment refers to the external environment such as the equipment room, power supply, and heat dissipation where the equipment operates. This is the basic condition for the equipment to operate. For the maintenance of the equipment operating environment, the staff can only complete it by visiting the site in person.

In order to protect the BGP protocol from attacks, Keychain authentication can be used between BGP neighbors to reduce the possibility of attacks. The keychain has a set of passwords that can be automatically switched according to the configuration, which is suitable for networks with high security requirements.

In the IS-IS network shown in the figure, R1 introduces the default route through the "default-route-advertise always level-1" command. Which of the following descriptions is wrong?

Which of the following operations does a network engineer not need to perform when processing a single-hop BFD session Dom?

Which of the following limitations of traditional networks do not include?

According to this picture, cooked I'] can be judged?

In the OSPFv3 network shown in the figure, the interconnected ports of R1, R2, and R3 have OSPFv3 enabled, and the Router ID of each device is 10.0.X.X, where x is the device number. Check the detailed information of a certain LSA on R3, and you can infer from the output information that R1 and R2 are DRs in the network.

In a certain MPLS network, the LSP information of R1 and R3 is shown in the figure. At this time, the administrator enters the command ping -a 1.1.1.1 3.3.3.3 on R1. Which of the following descriptions of this scenario is correct?

The equipment operating environment refers to the external environment such as the equipment room, power supply, and heat dissipation where the equipment operates. This is the basic condition for the equipment to operate. For the maintenance of the equipment operating environment, the staff can only complete it by visiting the site in person.

There are many types of MAC address entries on the switch. Which of the following types are manually configured by the user and cannot be aged? (Multiple choice)

As shown in the figure, R1, R2, and R3 run WPLS, and the administrator configures a static LSP from the 1.1.1.0/24 network segment to the 3.3.3.0/24 network segment. Which of the following descriptions of this scene are correct? (Multiple choice)

The exchange of Hello messages between two LSRs (Label switching Routers) triggers the establishment of an LDP session. The Hello message carries the transport address. The device with the smaller transport address will act as the active party and initiate the establishment of a TCP connection.

A company purchased private lines from two operators. In order to optimize the lines, the company used the 6GP protocol to learn from two Route entries that operate off. However, after the enterprise found that this configuration, the traffic of the port route increased greatly, and the network engineering arrangement After investigation, it was found that the traffic of the two operators was passed to each other through the enterprise egress router. Therefore, the enterprise intends to use the routing stra

When executing a cutover project, network engineers can perform remote operations at the customer's network maintenance center and guide on-site construction personnel to complete hardware-related operations, such as powering on equipment and connecting equipment.

According to the configuration shown in the figure below, you can know that how many interfaces of R4 are advertised into IS-IS?

In the Hub&Spoke network shown in the figure, Hub-PE can allow local AS number duplication through manual configuration to achieve correct routing transmission.

As shown in the figure, OSPF is enabled on all interfaces of the router. Which of the following statements is correct?

A router runs OSPF, and the output information is shown in the figure. Which of the following statements is correct?

MPLS needs to assign labels to messages in advance and establish an LSP before it can forward messages. LSP is divided into static LSP and dynamic LSP. Which of the following protocols can be used to establish a dynamic LSP? (Multiple choice)

A network engineer outputs the following information when troubleshooting OSPF. Based on this, determine which reason causes the adjacency relationship to fail to be established normally?

For which packets can Huawei equipment perform traffic suppression? (Multiple choice)

When the switch is configured with port isolation function, by default, different hosts belonging to the same VLAN cannot communicate at layer 1 and layer 3.

A network engineer accidentally deleted the IP address of an interface through the command line. If he wants to view the deleted IP address, which of the following information should he query?

The LSP information generated by a certain IS-IS router is shown in the figure. From the LSP information, it can be inferred that the router is not the DIS of this link.

On the same switch interface, the administrator can only configure traffic suppression for one of the following: broadcast, unknown multicast, unknown unicast, known multicast, and known unicast packets.

To support the processing and calculation of IPv6 routes, IS-IS adds a new MLPID in TLV No. 129. MLPID is an 8-bit field that identifies a network layer protocol message. Which of the following is the MLPID value for IPv6?