拥有CCNP认证，能够参加300-815考试，同时拥有相关的历年真题和学习资料。适用于Cisco Collaboration领域的300-815考试，即CLACCM考试。

If OSPF is running on this network, how does Router 2 handle traffic from Site B to 10.10.13/25 at Site A?

Topic 1Which network allows devices to communicate without the need to access the Internet?

Which Cisco 2950 switch command or set of commands would be used to create a Virtual LAN (VLAN) named MARKETING with a VLAN number of 25?

Topic 1What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?

Which of the following accurately describes the purpose of a trunk?

You are the network administrator for your company and have configured Cisco Discovery Protocol (CDP) in your network. You recently noticed that when devices send large numbers of CDP neighbor announcements, some devices are crashing. You decide to disable CDP on the router. Which command should you use to achieve the objective?

Which two fields are present in the output of the show ip interface brief command? (Choose two.)

Topic 1Refer to the exhibit. Which prefix does Router1 use for traffic to Host A?

Topic 1How do TCP and UDP differ in the way that they establish a connection between two endpoints?

Users on the LAN are unable to access the Internet. How would you correct the immediate problem? Router# show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet 0/0 unassigned YES unset down down FastEthernet 0/1 172.16.1.254 YES NVRAM up up Serial0/0 200.16.4.25 YES NVRAM administratively down down Serial0/1 unassigned YES unset down down

IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1: 1. Configure reachability to the switch SW1 LAN subnet in router R2. 2. Configure default reachabil

All physical cabling is in place. Router R4 and PCI are fully configured and inaccessible. R4's WAN interfaces use .4 in the last octet for each subnet. Configurations should ensure that connectivity is established end-to-end. 1 . Configure static routing to ensure RI prefers the path through R2 to reach only PCI on R4's LAN 2. Configure static routing that ensures traffic sourced from RI will take an alternate path through R3 to PCI in the event of an outage along the primary path 3. Configure default rout

Configure IPv4 and IPv6 connectivity between two routers. For IPv4, use a /28 network from the 192.168.1.0/24 private range. For IPv6, use the first /64 subnet from the 2001:0db8:aaaa::/48 subnet. 1. Using Ethernet0/1 on routers R1 and R2, configure the next usable/28 from the 192.168.1.0/24 range. The network 192.168.1.0/28 is unavailable. 2. For the IPv4 /28 subnet, router R1 must be configured with the first usable host address. 3. For the IPv4 /28 subnet, router R2 must be configured with the last usa

Topic 1Which statement identifies the functionality of virtual machines?

Which Cisco IOS Cisco Discovery Protocol (CDP) command displays the IP address of the directly connected Cisco devices?

Which Cisco Internetwork Operating System (IOS) command is used to view the number of Enhanced Interior Gateway Routing Protocol (EIGRP) packets that are sent and received?

All physical cabling is in place. Router R4 and PCI are fully configured and inaccessible. R4's WAN interfaces use .4 in the last octet for each subnet. Configurations should ensure that connectivity is established end-to-end. 1 . Configure static routing to ensure RI prefers the path through R2 to reach only PCI on R4's LAN 2. Configure static routing that ensures traffic sourced from RI will take an alternate path through R3 to PCI in the event of an outage along the primary path 3. Configure default rout

Which two modes are Cisco Internetwork Operating System (IOS) operating modes? (Choose two.)

Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured 1. Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends 2 Configure the EtherChannel as a trunk link. 3. Configure the trunk link with 802.1 q tags. 4. Configure the native VLAN of the EtherChannel as VLAN 15. Answer as below configuration:

When a packet is forwarded through a network from one host to another host, which of the following fields in the Ethernet frame will change at every hop?

What will be the effects of executing the following set of commands? (Choose all that apply.) router(config)# router eigrp 44 router (config-router)# network 10.0.0.0 router (config-router)# network 192.168.5.0

Topic 1A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two.)

You are configuring a WAN connection between two offices. You cannot ping between the routers in a test. The Serial0 interface on RouterA is connected to the Serial1 interface on RouterB. The commands you have executed are shown below. What is the problem with the configuration?

Topic 1When configuring IPv6 on an interface, which two IPv6 multicast groups are joined? (Choose two.)

Topic 1Which 802.11 frame type is Association Response?

Topic 1Which command automatically generates an IPv6 address from a specified IPv6 prefix and MAC address of an interface?

You are connecting a new computer to Switch55. The new computer should be placed in the Accounting VLAN. You execute the show vlan command and get the following output: Examine the additional network diagram. What action should you take to place the new computer in the Accounting VLAN and allow for inter-VLAN routing?

A router running EIGRP has learned the same route from two different paths Which parameter does the router use to select the best path?

Drag and drop the functions from the left onto the correct network components on the right

Topic 1In which way does a spine-and-leaf architecture allow for scalability in a network when additional access ports are required?

Topic 1An engineer must configure a /30 subnet between two routes. Which usable IP address and subnet mask combination meetsthis criteria?

Topic 1Refer to the exhibit. Which type of route does R1 use to reach host 10.10.13.10/32?

You are the network administrator for your company. You have installed a new router in your network. You want to establish a remote connection from your computer to the new router so it can be configured. You are not concerned about security during the remote connection. Which Cisco IOS command should you use to accomplish the task?

What two devices can be connected to a router WAN serial interface that can provide clocking? (Choose two.)

You are creating a configuration to use on a switch. The configuration must enable you to remotely manage the switch. Which of the following command sets is correct? (Assume the commands are executed at the correct prompt.)