为通过 CCNP 350-801 考试做好准备：2026年更新的历年真题。涵盖思科协作技术相关的内容，包括 350-801 CLCOR 和 SPOTO 等知识点。

Refer to the exhibit. Refer to the exhibit. An engineer Is designing a multicampus Layer 3 Infrastructure using EIGRP as the routing protocol. The design must provide quick replies to queries In the event of a downlink, prevent unnecessary queries, and ensure that traffic does not unnecessarily transit the access layer. Which two actions must the engineer take for the network design? (Choose two.)

Topic 1A network solution is being designed for a company that connects to multiple Internet service providers. Which Ciscoproprietary BGP path attribute will influence outbound traffic flow?

Topic 1Company A recently acquired another company. Users of the newly acquired company must be able to access a server thatexists on Company As network, both companies use overlapping IP address ranges. Which action conserves IP addressspace and provides access to the server?

Which command enables GLBP on an interface?

Topic 1Refer to the exhibit. Which solution decreases the EIGRP convergence time?

Which statement best describes the function of Hot Standby Router Protocol (HSRP)?

What command disables 802.1x authentication on a port and permits traffic without authentication?

Topic 1A company is using OSPF between its HQ location and a branch office. HQ is assigned area 0 and the branch office isassigned area 1. The company purchases a second branch office, but due to circuit delays to HQ, it decides to connect thenew branch office to the existing branch office as a temporary measure. The new branch office is assigned to area 2. WhichOSPF configuration enables all three locations to exchange routes?

Topic 1A customer with an IPv4 only network topology wants to enable IPv6 connectivity while preserving the IPv4 topologyservices. The customer plans to migrate IPv4 services to the IPv6 topology, then decommission the IPv4 topology. Whichtopology supports these requirements?

How does a model-driven telemetry dial-out approach function?

Topic 1Which design consideration should be observed when EIGRP is configured on Data Center switches?

The partial output displayed in the exhibit is a result of what IOS command? (Click on the Exhibit(s) button.)

Topic 1Refer to the exhibit. EIGRP has been configured on all links. The spoke nodes have been configured as EIGRP stubs, andthe WAN links to R3 have higher bandwidth and lower delay than the WAN links to R4. When a link failure occurs at the R1-R2 link, what happens to traffic on R1 that is destined for a subnet attached to R2?

Topic 1Which method will filter routes between EIGRP neighbors within the same autonomous system?

Which feature provides the capability for intra-VN traffic filtering and control within the Cisco SO-Access architecture?

What command would be used to display detailed information regarding VRRP groups on the switch?

You have been assigned to create a plan to implement HSRP on the router connecting your company's network to the Internet. The router should be the active router in the HSRP group. On the active router, the following conditions should be met: Enable preemption with no delay Set Hello timer to 10 seconds and hold time to 25 seconds Set the priority to 150 Which of the following commands should be included in the plan to meet the given requirements? (Choose all that apply.)

Topic 1A router running ISIS is showing high CPU and bandwidth utilization. An engineer discovers that the router is configured asL1/L2 and has L1 and L2 neighbors. Which step optimizes the design to address the issue?

Topic 1When a network is designed using IS-IS, which two circuit types are supported? (Choose two.)

An engineer is designing a campus network with Cisco Catalyst 95CO switches in the aggression layer. The design requires running nonblocking Layer 2 MEC from the aggregation layer to the access layer. The Catalyst switches are located on different campus floors for availability reasons, and each access switch veil contam a single VLAN. Which technology must the engineer choose for the aggregation switches in the design?

Assuming that preempt is not configured, when does a router in an HSRP group assume the role of the active router for the group?

Topic 1What are two valid scaling techniques when an EIGRP network is designed that consists of more than 1000 routers?(Choose two.)

In a multicast network, which condition must be met for an RPF check to be performed on the RP address'?

Topic 1Which two BGP features will result in successful route exchanges between eBGP neighbors sharing the same AS number?(Choose two.)

Topic 1A company is running BGP on a single router, which has two connections to the same ISP. Which BGP feature ensurestraffic is load balanced across the two links to the ISP?

What command would display a single line of information for each virtual gateway or virtual forwarder on a switch?

You have configured three routers in HSRP group 10 to provide gateway redundancy for VLAN 56. Your intention was for Router 1 to be the active router in the group and for Router 3 to be the standby router. Furthermore, in the event that Router 1 became unavailable, resulting in Router 3 becoming active, you intended for Router 1 to resume its role as active when it came back online. However, you discover that in practice, Router 1 does NOT resume the active role when it comes back online. What command shoul

Topic 1Which design consideration must be made when using IPv6 overlay tunnels?